9159金沙游戏场-9159金沙游戏艺场官网

  • 地址:济南市槐荫区鑫苑世家公馆2号楼2603室
  • 电话:0531-87568508 /
  • 手机:18653128690
  • 邮箱:jnyhrs@163.com
  • 无尘车间装潢条件达到要做出哪些改善?
    来源: 浏览:次 发布日期:2018-08-17
    无尘车间的围护结构和房间内部装潢质料宜选用气密泄慵好,再是在温度、湿度等改动时,本身变形小的质料;墙壁和顶棚表面应光洁平整、不起灰、不落尘、耐腐蚀、耐冲击、易清洗。为了使无尘车间的建筑表面尽量少积灰、易清扫,应在建筑构造上避免或减少凹凸面,墙面与地上、墙面与顶棚、墙面与墙面的相接处也不宜做成一般的直角,宜做成半径大于或等于50mm的圆角。壁面涂层的色彩要和谐、雅致、素淡,以便于显现壁面上的污染物。同样,地上也应做到平整、无间隙隙、耐磨、耐腐蚀、耐冲击、不积聚静电、易除尘清洗。
    Surrounding structure and interior decoration materials of dust-free workshop should be chosen with good air tightness, and materials with small deformation should be used when the temperature and humidity change; the walls and roof surfaces should be smooth and smooth, non-ash, non-falling dust, corrosion-resistant, impact-resistant and easy to clean. In order to make the building surface of dust-free workshop as little as possible ash, easy to clean, should avoid or reduce the concave and convex surface in the building structure, wall and ground, wall and roof, wall and wall joints should not be made into a general right angle, should be made into a radius greater than or equal to 50 mm rounded angle. The color of the wall coating should be harmonious, elegant and plain, so as to display the pollutants on the wall. Similarly, the ground should be flat, seamless, wear-resistant, corrosion-resistant, impact-resistant, non-accumulation of static electricity, easy to clean dust.
    为了避免 技术实现 夹层内的微粒、微生物污染无尘车间,应对其墙面和顶棚抹灰(应为高等级抹灰)。如果需要在 技术实现 夹层内更换高效过滤器,夹层内的墙面,顶棚还应刷上涂料罩面。送风道、回风道、回风地沟的表面装潢应与整个送风、回风系统相适应,并易于清扫消毒。
    空气净化工程
    In order to avoid the dust-free workshop polluted by particulates and microorganisms in the technical intercalation, the wall and ceiling should be plastered (advanced plastering should be used). If you need to replace high-efficiency filters in the technical sandwich, sandwich wall, the ceiling should also be painted with a cover. The surface decoration of the air supply duct, air return duct and air return ditch should be suitable for the whole air supply and air return system and be easy to clean and disinfect.
    门窗与内墙面宜平整,尽量不留窗台。外窗的层数和门窗的构造要按照露天空气的污染程度,房间内部外策划温度、湿度,房间内部外压差,以及客厅的洁净度等圆素综合揣摩,务求其构造能对空气和水蒸气起到密封感化,使污染物不易从外部侵入,并能避免内表面结露。为了防止洁净区域内部的交叉污染,房间内部不同洁净度客厅之间的内门、内窗以及隔断处等的缝隙均宜密封。门窗造型要easy,不得设置门槛,以便清扫。
    Doors and windows and inner walls should be smooth, try not to leave window sills. The number of outer windows and the structure of doors and windows should be considered comprehensively according to the pollution degree of outdoor air, indoor and outdoor design temperature, humidity, indoor and outdoor pressure difference, as well as room cleanliness and other factors, so as to make the structure of the air and water vapor can be sealed, so that the pollutants are not easy to intrude from the outside, and can avoid condensation on the inner surface. In order to prevent cross-contamination within the clean area, the cracks in the internal doors, windows and partitions between rooms with different cleanliness should be sealed. Door and window modelling should be simple, and no threshold should be set up for cleaning.
    为了保证厂房的洁净度,洁净区要做到窗户密封。空调区与非空调区之间的窗户要设双层窗,至少此道一层为固定窗。其余,不同洁净级别无尘车间之间的联系门要密闭、平整、造型easy,且门应向级别高的方向开启。
    In order to ensure the cleanliness of the workshop, the clean area must be sealed by windows. There should be double windows between the air conditioning area and the non air conditioning area, at least one of which is a fixed window. In addition, the connection doors of different cleanliness levels should be sealed, flat and simple, and the doors should be opened in the direction of higher level.
    XML 地图 | Sitemap 地图